RONDA 1032 Swiss Made Watch Movement, 2 Hands, Without Disk, Height 0

Ronda 1032 Swiss Made Slimtech Quartz MovementRonda 1032 is a Swiss Made quartz watch movement from RONDA’s Slimtech 1000 line. It is designed for compact watches that require a small, thin, and reliable 2-hand quartz movement without a date display. This movement is supplied without a date disk, making it suitable for dials that only use hour and minute hands. Before installation, the watchmaker should confirm the case fitting, dial feet position, stem height, hand sizes, and available space above the battery.The official RONDA data for the Ronda 1032 lists it as a 3¾ x 6”’ movement with total dimensions of 9.00 x 13.20mm and a case fitting size of 9.00 x 13.50mm. The movement height is 1.95mm, while the height over the standard battery is 2.10mm. These measurements are important when replacing a movement in a compact watch case, especially in ladies’ watches or small dress watches where internal space is limited.Ronda 1032 Function and LayoutThe Ronda 1032 is a 2-hand quartz movement. It displays hours and minutes only, with no seconds hand and no date function. This simple layout is useful for watches that require a clean dial design or very thin movement construction. Since it is supplied without a date disk, it should not be used for watches that require a working date window.The movement uses Battery 317 with 1.5V voltage. Official RONDA technical data lists a standard battery life of up to 60 months depending on the version and battery conditions. Battery life can vary depending on storage time, contact cleanliness, operating temperature, and the condition of the watch case. A fresh battery and clean contacts are important for stable operation after installation.Replacement and Service NotesThe Ronda 1032 is normally replaced when the original movement has stopped working, has poor battery contact, has been damaged by battery leakage, or no longer drives the hands correctly. Before replacing the movement, the watchmaker should check the battery, crown, stem, hand clearance, dial contact, and case pressure. Some faults may come from external parts, not the movement itself.Because this movement is small and thin, it should be handled carefully during fitting. The coil, circuit, and contact areas should not be touched with metal tools or bare fingers. The hands must be installed with the correct pressure and correct clearance. If the hands are pressed too low or touch the dial, crystal, or each other, the movement may stop or consume more power.Professional ApplicationRonda 1032 is suitable for professional watch repair and movement replacement in compact quartz watches. Its small size makes it useful when case space is limited, but it also means that accurate fitting is important. The stem length must be adjusted correctly, and the crown must engage smoothly in the setting position. After installation, the watch should be tested for hand movement, setting function, battery contact, and case clearance.The Ronda 1032 should be selected only when the original watch uses the same movement size, height, hand fitting, and no-date layout. Matching the movement mechanically is as important as matching the caliber number, because incorrect case fitting can create pressure on the movement or prevent the stem from operating correctly.Technical SpecificationsBrand: RONDACaliber: 1032Line: Slimtech 1000Movement Type: Swiss Made quartzDisplay: 2 handsDate: Without disk / no dateSize: 3¾ x 6”’Diameter: 9.00 x 13.20mmCase Fitting: 9.00 x 13.50mmMovement Height: 1.95mmHeight Over Standard Battery: 2.10mmMovement Rest: 0.20mmHeight Over Stem: 0.62mmStem Thread: 0.70mmBattery: 317Battery Voltage: 1.5VJewels: 7Operating Temperature: 0°C to 50°CFeaturesSwiss Made RONDA quartz movementRonda 1032 Slimtech caliber2-hand displayWithout date diskCompact movement size1.95mm movement height7 jewelsBattery 317Suitable for small watch casesProfessional replacement movementFunction and PurposeThe Ronda 1032 is designed to operate hour and minute hands in compact quartz watches. It is used when the original 2-hand no-date movement is defective, damaged, or no longer suitable for service. It is not intended for watches that require a seconds hand or date display.CompatibilityCompatible with watches that use RONDA 1032 or a movement with matching:2-hand display layoutNo-date dial design9.00 x 13.20mm movement dimensions9.00 x 13.50mm case fitting1.95mm movement heightCorrect stem heightCorrect hand fittingBattery 317 clearanceFrequently Asked Questions (FAQ)Q: Does the Ronda 1032 have a date function? A: No, the Ronda 1032 is a 2-hand movement supplied without a date disk.Q: What battery does the Ronda 1032 use? A: The movement uses Battery 317 with 1.5V voltage.Q: What is the height of the Ronda 1032 movement? A: The official movement height is 1.95mm, and the height over the standard battery is 2.10mm.Q: Is this movement suitable for watches with a seconds hand? A: No, this version is a 2-hand movement for hour and minute hands only.Shipping & Delivery�� Phone & WhatsApp: 20 122 323 9604�� Email: [email protected]�� Email: [email protected]�� Website: https://www.swisswh.com�� Facebook: https://www.facebook.com/WatchHouseSparePartsWe offer worldwide shipping via DHL and UPS. Every order is carefully packed to ensure maximum protection during transit. Orders are dispatched within 1–2 business days, and delivery typically takes 3–7 business days depending on the destination country and customs procedures.